To Dunk,,, or not to Dunk.

[Cheech]

This is part 4 of the series.....

Along the way with this great Bearing discusion, a couple of people have mentioned submersing the trailer, and how this can damage the bearings because of the heat change sucking in the water.

Others have said that they dunk because they have to as the trailer is just not in enough to retrieve the boat.

I am a dunker.... But this has got me thinking,,,, if the main dunking problem is with heat during launching, and the main dunking requirement is due to retrieving,,,, then why not combine the 2 for the best advantage [smiley=idea.gif]

Why not launch without dunking. Stop reversing just before the hubs go under. That way you will not have the heat problem sucking water in. And when you come to retrieve, dunk as usual and this should not have any impact on the bearings as the hubs will be cold at that time.

What I have noticed is that launching just does not need the same water depth as retrieving does. I had just never considered altering what I do at launch compared to retrieve.

Is this one of those simple solutions that is under our nose and just gets missed?

So,,, what do you all think?

By the way, about a month ago I took out all my centre rollers and greased the shafts and the inside of the rubber. The difference is absolutely amazing. Previously I had to use a fair bit of grunt to push the boat off the trailer till it was about half in. (less for steep ramps) Now, All I have to do is give it an initial push to break inertia, and then it just slides all the way off with no assistance. If anyone has any problems with getting a boat on or off, grease the centre rollers. It really makes a huge difference.

So, what do you think?

Cheech

[blaze]

Seems Like I am chasing you about Cheech
I dunk,
I am only 500m from my normal ramp, 15k from the other I use. Then when I go to St helens, 5hrs drive, I dont put the boat in the water that day cause I am to F***ed.
cheers
blaze

[Big_Kev]

Cheech sometimes I think you think to much.LOL
Also "Inertia" I think?

[Cheech]

Yeh, I knew it was wrong. Changed the c to an s and back and it still looked wrong, but could not be bothered looking in the dictionary. Have modified the post.

But is it a good idea??

[mackmauler]

Cheech, thats what I do, bearings still seem to go rusty after a good yrs use, still I think its best to keep them out of water when possible and after a tough days fishn be stuffed if ill keep em dry.

[Spaniard_King]

I would have to say my bearings would be under water each time my trailer goes into the wateR

Perrils of owning a largish boat I suppose 8)

Garry

[mako_5.2]

I manage to get my 17' in and out without putting the bearings in the water, having said that I am in the middle of converting it to dual axle and am not sure if I will be still able to do this. I had to put the rear axle further back and was expecting to have to at least wet the rear bearings. Should find out if it will be a problem next week. Following previous threads on b/buddies with interest as I thought this was my answer, not so sure now and I don't want to join the broken trailer brigade on the highway.

Cheers

[DAVE_S]

hi cheech that is a good idea dunk cold no dunk hot that idea for your center rolls very good if you got a mate with a lathe next time you take the shaft out get him to drill ahole up the guts and put a grease nipple in it did this to my cat trailer my be one day if i become your mate i can do this for you new to ausfish dave

[Kerry]

Some boats/trailers one could do that, others are simply impossible.

Cheers, Kerry.

[SeaSaw]

I drive on and off the trailer. I would be worried about the motor hitting the ramp on the launch if I didn't dunk the bearings. Bearings are cheaper than props to replace.

Mark

[mako_5.2]

Your boat it a lot bigger than mine . I also winch it off just in case I misjudge depth. You see a lot of people that put the trailer in to the top of the guards and just about float them off just to launch a 10' dinghy. Have seen the other extreme at Munna point, a group of new boaties (had to be) with a 6m quinnie bow rider backed down until the motor was at the water line and pushed it off the trailer. Did not float on sand so they winched it back on to the trailer and nearly put it in up to the towball next time.

[Mr__Bean]

I have to dunk due to size of boat and prop clearance but wish I could leave as much as possible out of the saltwater (acid).

I also agree that roller care is important but beware of greasing rubber rollers. Rubber rollers are not grease and oil resistant and will deteriorate rapidly if sitting in normal grease.

If they are the plastic type they should be fine, but if they are the rubber ones you really should use a rubber grease or just use soap in there.

Food for thought.

- Bean

[finga64]

me, the only thing I dunk are scotch fingers. [smiley=thumbsup.gif]
But I'm lucky (or unlucky depending on view point), my boats aren't big enough to dunk the trailer.(little one - 3.75m & bigger one 5m)
I also winch both boats off the trailer as well just in case of unseen rock or log or whatever. Got into that habit after lauching the little boat into Lesley dam at Warwick and smashed the transducer on a log
But if it feels good, do it

[nonibbles]

"Got into that habit after lauching the little boat into Lesley dam at Warwick and smashed the transducer on a log
But if it feels good, do it"

Nah, can't imagine that feeling good at all.

[finga64]

No nonibles
smashing the bl--dy transducer don't feel good. Made me quite ill actually. It was only 4 or 5 weeks old at the time.

If it feels good to dunk the trailer, then dunk. If not don't.

I did some work on the little old trailer before easter and found a date stamp. 12/5/1970
That's what happens when you don't dunk.
P.S. I have 2*2 leaf springs to give away if anybody wants them. A bit rusty but still usable. I put some galv. ones in.