anchor rope

[dnej]

Jeremy,
The Whitworth stuff is a composite. For an example, the real Dyneema, non composite gear ,in 6mm,is rated to a 4200kg breaking strain, and should be around $ 8, or 9 dollars per metre.I think there is a place in Melbourne.
David
Was it not something to freezing crabs,as an example?

[Jeremy]

Thanks for the clarification on the dyneema.

PM sent to avoid hijacking this thread.

Jeremy

[Getout]

Dyneema anchor rope?????
An expensive exercise when you get the anchor stuck!!!!!
Also, I'd be worried about an open anchor well on the fordeck. I have known of anchors to be thrown out of front hatches to foul the prop and cause a capsize during a bar crossing.

[Chimo]

Agree with Getout about the open anchor well on the fordeck. Have been going to comment on this earlier but due to being too easily distracted etc by other things it didn't happen. If your going to instal a bin on the fordeck get one with a lid with a catch to hold things in place till you need them. Much better and safer than having stuff flopping around in the bow and in front of the front seat and able to fall free when you least want it to.

Cheers
Chimo

[Sea-Dog]

maybe take your anchor off and then motor out into a clear area and let all of your anchor rope out and trail it behind you for a while and get all of the twists out of it

then retrieve it all and lay it neatly into your anchor well in a figure 8

should retrieve nicely if there are no twists and kinks in it

many people put out 60++ metres when offshore, and it goes out and comes back nicely

cheers

Mick

Hey Mick, I was setting up an anchor rope for a new dan buoy on the trawler I was working on.

New 50M role of 6mm nylon rope. I let it out the back of the trawler whilst steaming along and tied the end off.

The only problem was that the lay of the rope acted as a long skinny propeller and it set up a massive twist in the rope.

When I pulled it all back onboard, it turned into a giant multiple bimini twist.

I had to untwist it manually on deck.

It would have been OK if I'd had a decent swivel attached to the trawler end I suppose.

[ronnien]

i use the kill bin, 4.4mtr flat bottom barra boat. but after reading this i am going down to see if i can get 1 of them wells in the casting deck.

ron.

[Sheik]

If you have a foredeck you can try this. Instead of cutting a hole in it, put three bollards in a triangle as big as possible on the foredeck triangle thingie and wind the rope around this. Drop the onchor on to floor, or alternatiely, drop some 150mm pipe through the foredeck or tie it onto the bow rails and poke the thin end of your anchor into this. ALl tidy it doesnt rattle and it also gives you grip if you happen to be castnetting from the front deck.

[Horse]

No need for a lid. The rope goes in first then chain and anchor. I used a occy strap on the anchor in rough conditions

[Trev_ally]

If you already know the approximate depth of water you regularly fish in try having the anchor rigged with a suitable length of rope. Works for me. Just remember to have a legal, adequate full anchor rope on board and handy just in case. Hope this helps.

[garman1]

My brother was here the other week and complained that the anchor rope was fairly thin, I said I needed the length in case i got into deeper water, his solution which sounds good is to work out what depth of water you fish in normally and use nice think rope for that depth and then keep the thinner rope which is spliced onto the thicker rope for the deeper water, that I haven't got into yet........... It is a lot easier on your hands using thicker rope.

So you end up with anchor, chain, thicker rope (used often) then thinner rope for the odd occasions you might go into deeper water. I only have a 4.3 mx boat so I don't float around in 50 metres of water etc. I thought this idea wasn't too bad and my usual deckies thought the idea was great.............................